Jailbreak 4.3.5 iOS for iPhone 4, 3GS, iPod Touch 4G, 3G and iPad Using RedSn0w [How To]

22/12/2011 22:26


iOS 4.3.5 was released by Apple as a minor Update to previous version (i.e. iOS 4.3.4) with 
only some of the security improvements. And it can be jailbroken using RedSn0w. This 
jailbreak does not support iPad 2 and it is a tethered jailbreak, which means every time 
you reboot your iOS device, you will have to connect it to the computer and boot it using 
the RedSn0w.
RedSn0w 0.9.8b4 can jailbreak iOS 4.3.5 on iPhone 4, 3GS, iPod Touch 4G, 3G and iPad 1. As 
stated before it cannot jailbreak iPad 2 because iPad 2 features an A5 Chip due to which it 
is hard for jailbreakers to jailbreak it. However it can be jailbroken using JailbreakMe on 
iOS 4.3.3. Follow the step by step guide posted below to jailbreak iOS 4.3.5 on iPhone, 
iPod touch and iPad.
How to Jailbreak iOS 4.3.5 for iPhone, iPod Touch and iPad
Step 1: First of all you will have to download iOS 4.3.5 as well iOS 4.3.4 IPSW Firmware 
because you will need to point RedSn0w to iOS 4.3.4 in order to jailbreak iOS 4.3.5.
iOS 4.3.5 IPSW Firmware Download from Apple
iOS 4.3.4 IPSW Firmware Download from Apple
Step 2: Also download RedSn0w 0.9.8b4 for Windows or Mac and the latest version of iTunes. 
After downloading RedSn0w, extract it and launch it.
Download RedSn0w for    WIND OWS  & MAC  
Step 3: Now after RedSn0w launches, select iOS 4.3.4 IPSW Firmware you previously 
downloaded in Step 1 and RedSn0w will start to recognize the firmware, once it does, you 
will be taken to next screen and from there, Check "Install Cydia". If you want, you can 
also select Multitasking and Battery Percentage and click "Next".
Step 4: Now you will have to connect your device in to the computer and put it into DFU 
Mode. To do so, follow these steps:
Press and Hold "Power" button for three seconds
After that Press and Hold "Home" button without releasing the "Power" button for 10 more seconds
Now release "Power" Button but keep on holding the "Home" button until RedSn0w starts
Step 5: After that, you won`t have to do anything, RedSn0w will do its magic and your 
device will be jailbroken in few minutes. After your device is jailbroken, you will have to boot it using RedSn0w. Just follow the steps posted below to do so.

cell phones & accessories hot item

How to Boot Tethered iOS 4.3.5 After Jailbreak
Step 1: First of all, connect and power Off your device and launch RedSn0w and once again 
select iOS 4.3.4 IPSW Firmware you downloaded previously.
Step 2: After that deselect "Install Cydia" and every other option and select only "Just 
Boot Tethered". Now you will again have to put your device into the DFU mode. Follow the 
instructions above to do so.
Step 3: Now if you successfully put your device in DFU mode, you will see that RedSn0w will 
again start to work on its own. And at this stage, your device will be showing a Pineapple Logo instead of Apple's Logo at the start up screen. And your device will be in its fully functional state in 2 minutes.
Remember that this is a tethered jailbreak and you will have to boot your device using 
RedSn0w each and every time you reboot it.